NLM Evo X – Nearing Completion
Our own salesman Rich’s Evo has come a long way from its bolt on power. We took on the build with an incredible list of parts in hopes to make numbers for the record books. After all was assembled and installed, we hit the dyno for tuning. To break in the motor, the RIP STI Evo made over 600whp and 500tq! Keep in mind this was all done on a mainline dyno, low reading numbers compared to most other dynamometers. Once the break in was complete, we hopped back on the rollers to give her a go with some serious boost, timing and ethanol. On e75 and roughly 35psi, with minimal timing she made over 700! We ran into an issue with the ignition, so once she gets her upgraded coil packs, shell hit the rollers again and see what she can do at near 50psi of boost and almost pure 98% ethanol! stay tuned for the final numbers. Full build list as of right now, and some pictures/videos below. Will be updating this list with more pictures videos and numbers as we continue!
EXHAUST & INTERCOOLER MISC
– ETS Extreme Exhaust
– ETS RACE Test Pipe – ETS 4 inch Intercooler
– ETS 2.5″ Lower Intercooler Pipe Kit
– ETS 2.5″ Upper Intercooler Pipe Kit
TURBO KIT
– ETS Turbo kit
a. Stainless Steel Downpipe
b. Exhaust Manifold
c. 2x Tial MVS Wastegates
d. 2x Wastegate Dump Tubes
e. 2.5″ Upper Intercooler Pipe
f. Oil Feed and Drain Lines
g. Water Feed and Drain Lines
h. Turbo Gaskets and Hardware
i. ETS Clamps and Couplers
– Custom Chameleon 4inch MAF Intake
– Precision PT6466 GEN 2 BB Turbo
FUEL
– Fuel Injector Clinic Injector Set x4 2150s
– Radium Engineering Dual Fuel pump w/ 2x AEM 50-1200 E85
– Radium Fuel Pressure Regulator
– Radium Fuel Filter & Feed kit
– Radium Fuel lines & Fittings
– Radium Fuel Rail Kit + Gauge
– Radium Pulse Dampener
MOTOR
– Darton Sleeves
– Manley TurboTuff Rod
– Manley Conrods TTuff I-Bm
– Wiseco 1400 HD Pistons set
– ACL Race Series Main Bearings
– ARP Custom Age CA625+ Head Stud kit
– GSC S3 Stage 3 Cams
– HEADGAMES – 031 4b Pocket ‘’Race” – Bronze guides – Valve job, chambers, lash, mill – Manley locks (includes valve seals)
– GSC beehive spring-kit
– HG custom retainers
– Ferrea 6000 series valves
– Aluminum valve cover
DRIVETRAIN
– EXEDY Hyper Triple Cerametallic Clutch Rigid Disc Pull Type Cover w/ Hyper Accessory Kit
– Driveshaft Stage 5 Rear Axles
– Torque solutions Engine & Tranny mounts
– Sheps Center Diff Pin Kit
– XDrive 4.18 Final Drive
– STM-Spec D2/Swift Drag Racing Coilovers
GAUGES & MISC
– Okada Projects Plasma Direct Coil Packs
– ATI Center Dash Pod
– AEM Oil Pressure Gauge
– AEM Fail safe wideband/boost Gauge
– AEM 50 PSI Boost Gauge
– AEM Fuel Pressure Gauge
– GS Boost Controller Electronic
– EVO III Sparco Seats
– OMNI 4 BAR Map Sensor
– Driven Fab Catchcan/coolant overflow Tank
– TephraXMOD V3